fredag den 10. maj 2013

Visiting Kennedy Space Center

This month I'll mention my journey to USA to visit my sister, who lives there. I also visited Kennedy Space Center's visitor complex, which is located near Cape Canaveral in Florida.

I have always loved space exploration, and being at the Kennedy Space Center feels like Heaven! There is so much to see and do. I went on a tour to visit the historic launch-pads at Cape Canaveral from where the different space missions and satellites have been launched. The highlight of the tour was visiting the control centre from where the first american flew into space. Allan Shepard's trip was a short one: he returned to Earth after just 15 minutes in space. However, the russian cosmonaut Yuri Gagarin was the first human in space - he went there just 23 days before Shepard!

I am in the control center with my fingers
on the launch button!

This Mercury-Redstone rocket launched
Alan Shepard into space in 1961.
 If you ever get the opportunity, do pay a visit to the Kennedy Space Center. I can heartily recommend it.

OZ1BXM, Lars Petersen, oz1bxm.dk

mandag den 1. april 2013

SSPA for 2 meters - project about to finish

Since last time, I have performed the SSPA smoke test. I adjusted the bias of the LDMOS transistor and set it to 3.5 A drain current at 48 V DC. Some heat was developed, but the cooling system could easily deal with it. Rf input and RF output were both connected to 50 ohms resistors. No oscillation was observed, which is good. Conclusion: so far, so good. Smoketest passed.

Many components, cables, relays, fuses, a sequencer, a high-current switch, and so on are used in the SSPA. It takes considerable time to mount them and connect the wires. As this is a prototype, some errors will happen in between. You learn from your errors - but they consume time. Today I can happily tell you, that the project is soon to be finished. The end is in sight!


One of the SSPA sidepanels seen from inside the cabinet.
The picture above shows how one of the side panels is equipped. Clicking the picture will make the text on the picture readable.

73 from OZ1BXM Lars Petersen  Visit my homepage: www.oz1bxm.dk


fredag den 1. marts 2013

SSPA for 2 meters - 1 kW module

If you want to explore more details of the amplifier project, I recommend an article by W6PQL: "Solid state 1 kW Linear Amplifier for 2 Meters". It appeared in QST October 2012.

I decided to buy the amplifier module as a kit from James Klitzing, W6PQL, where all components were included. The copper heat spreader, however, was purchased from PE1RKI Bert. I opted for the version prepared for watercooling.

The core of the SSPA is the 1 kW amplifier module. The module is built around the LDMOS transistor MRFE6VP61K25H from Freescale. This device can operate between 1.8 MHz and 600 MHz and delivers 1250 W output. In this application, the output is limited to 1000 W.

The photo below shows how small the 1 kW module is. Dimensions are 12 cm x 8 cm. But the copper heat spreader is 2 cm thick and weights 1.5 kg. This size is necessary, because the heat spreader must be able to transfer up to 400 W.

1 kW amplifier module for 2 meters.


A low-pass filter follows the amplifier module in order to suppress harmonics of 144 MHz. The physical size of the PCB is the same as the amplifier module. A directional coupler is included, which allows monitoring of forward and reverse power.

1 kW low-pass filter for 2 meters.

This project is still in progress and the 'smoke test' should be completed soon.

Lars Petersen, OZ1BXM

Homepage: http://oz1bxm.dk 


fredag den 1. februar 2013

SSPA for 2 meters - Watercooling

The primary advantage of watercooling is its ability to transport heat away from the source (a transistor) to a secondary cooling surface (a radiator). This allows for large, more optimally designed radiators rather than small fins mounted directly on the heat source.

The disadvantage of watercooling is higher cost and complexity when compared to air cooling.

The picture below shows the components in a watercooled system. In my project, the PA transistor is soldered directly to the copper water block. The radiator is mounted on top of the cabinet and cooled by two large 140 mm fans. The pump and the reservoir is one single unit making the system more compact.

The watercooling system for my SSPA project is about twice as expensive as conventional air cooling. In return, I expect a quiet system which allows high-power transmission and human conversation in the schack at the same time!

OZ1BXM Lars Petersen

Homepage: http://oz1bxm.dk/

tirsdag den 1. januar 2013

SSPA for 2 meters - Cabinet

Building a Solid State Power Amplifier (SSPA) is my project this winter. I have chosen the 1 kW SSPA for 144 MHz as described by F1JRD in DUBUS 4/2010. I'll attempt 2 meter EME later this year, and a powerfull SSPA will become a key component in the set-up.

I have decided to build the cabinet first. I have found DIY alu-frames that can be taylored to many sizes. The cabinet's alu-framework is 30 cm wide, 15 cm high, and 15 cm deep. Furthermore, 2 mm alu-sheets are available from another source, and these sheets fit exactly into the alu-framework. This means no cumbersome cutting and bending of cabinet parts!

The SSPA cabinet.

Another feature of my new SSPA is watercooling. This cooling method is known and used among PC freaks. But as far as I know, only few radio amateurs use that technique. More on watercooling next month.

OZ1BXM Lars Petersen

My homepage: oz1bxm.dk

My latest 10 QSO



mandag den 17. december 2012

Merry Christmas - Happy New Year

It is Winter in Denmark right now. We had a lot of snow this December. As you can see in the picture below, our small garden is totally white!

Outdoor work is not longer possible. It is hazardous to climb a ladder or walk on a roof. So antenna work has to wait for higher temperatures. Indoor activities are at premium. I am waiting for some electronic kits to arrive from USA. I hope they will come before Christmas.

I am taking a 6 month leave from my job. The beginning of 2013 will (hopefully) be relaxing, and some travelling has already been planned. My wife and I would like to visit distant places.

Our garden viewed from the kitchen.

Dear reader. I wish you a Merry Christmas and a Happy new Year 2013! 

OZ1BXM Lars Petersen

My homepage: http://oz1bxm.dk

fredag den 30. november 2012

Homemade 1:2 balun

I need an 1:2 balun
My 20m loop antenna has about 100 ohm impedance at the 14 MHz resonance frequency. My coax-cable is a 50 ohm type. Transforming 100 ohms to 50 ohms can be accomplished by an antenna tuner, or by an HF balun. The inexpensive approach is using a balun.

Figure 1. Balun 1:2. Picture credit: OE7OPJ.

Winding the toroid
Please refer to the drawing by OE7OPJ in figure 1. The red wire begins at the UHF-connector's center pin. The black wire begins at the UHF-connector's ground pin. The two  wires "follow each other" for 6 windings, and then the black wire is connected to one of the output terminals. The red wire continues with 6 more windings and then connected to the UHF-connector's ground pin. Finally, a short wire connects the UHF-connector's center pin to the other output terminal.

Figur 2. The finished 1:2 balun.

My homemade balun can be seen in figure 2. The toroid core is TX36/23/15-4C65 from Ferroxcube. An alternative toroid can be Amidon FT-140-43. The core's outer diameter is 34 mm and the inner diameter is 22 mm (not critical). The teflon wire (AWG18) was purchased from dx-wire.de. The sealed ABS box (item G302) is from Velleman.

Figure 3. The balun is housed inside an ABS box.
Testing the balun
Testing an 1:2 balun is easy. You connect a resistor at the balanced terminals. Then you measure the impedance at the unbalanced port. This impedance should be ½ the resistance at the balanced terminals due to impedance ratio 2:1.

I connected a 50 ohm resistor at the balanced terminals. Then I measured 25 ohms at 14 MHz at the unbalanced end. Conclusion: The balun's impedance transformation is just right!

73 from OZ1BXM Lars Petersen

Visit my homepage: http://oz1bxm.dk