mandag den 1. juli 2013

SSPA for 2 meters - Finished project

Finally! My SSPA for 2 meters is now finished. The building process has been long, but the learning experience was good. The picture below shows the SSPA as seen from the front:
On top of cabinet:
Two black 140 mm fans cool the radiator. The air is taken in below the radiator.
The black radiator exchange heat between the cooling water and the air.
The cabinet:
Upper row: Output meters (forward and reflected power).
Center: Voltage and Amps are monitored.
Lower row: Water and heatspread temperature are monitored.
The square to the left: Switches and control lamps for 12V, 48V, and PTT.

You can read the full SSPA story on my homepage, where more than 20 SSPA pictures are found, and where I've calculated the cost of the project.

73 from OZ1BXM Lars


SSPA for 2 meters with Freescale MRFE6VP61K25H

søndag den 2. juni 2013

Polar bears in Copenhagen Zoo

I went to Copenhagen last weekend together with my wife to visit our daughter and her husband. As my daughter lives near Copenhagen Zoo, it was an easy decision to go there and spend the afternoon looking at wild animals. We spent most of the time in the new facility called The arctic Ring, which specializes in animals from the Arctic.

The polar bears are busy eating fish.

Two polar bears caught our eyes. They were busy eating fish, but as the fish were frozen inside a block of ice, it was a tough job for the bears to get the food out. However, it seemed as if they were entertained by the chore. And so were we!

Next month I'll tell you more on the progress of my 144 MHz SSPA.

OZ1BXM Lars Petersen

Homepage: oz1bxm.dk

fredag den 10. maj 2013

Visiting Kennedy Space Center

This month I'll mention my journey to USA to visit my sister, who lives there. I also visited Kennedy Space Center's visitor complex, which is located near Cape Canaveral in Florida.

I have always loved space exploration, and being at the Kennedy Space Center feels like Heaven! There is so much to see and do. I went on a tour to visit the historic launch-pads at Cape Canaveral from where the different space missions and satellites have been launched. The highlight of the tour was visiting the control centre from where the first american flew into space. Allan Shepard's trip was a short one: he returned to Earth after just 15 minutes in space. However, the russian cosmonaut Yuri Gagarin was the first human in space - he went there just 23 days before Shepard!

I am in the control center with my fingers
on the launch button!

This Mercury-Redstone rocket launched
Alan Shepard into space in 1961.
 If you ever get the opportunity, do pay a visit to the Kennedy Space Center. I can heartily recommend it.

OZ1BXM, Lars Petersen, oz1bxm.dk

mandag den 1. april 2013

SSPA for 2 meters - project about to finish

Since last time, I have performed the SSPA smoke test. I adjusted the bias of the LDMOS transistor and set it to 3.5 A drain current at 48 V DC. Some heat was developed, but the cooling system could easily deal with it. Rf input and RF output were both connected to 50 ohms resistors. No oscillation was observed, which is good. Conclusion: so far, so good. Smoketest passed.

Many components, cables, relays, fuses, a sequencer, a high-current switch, and so on are used in the SSPA. It takes considerable time to mount them and connect the wires. As this is a prototype, some errors will happen in between. You learn from your errors - but they consume time. Today I can happily tell you, that the project is soon to be finished. The end is in sight!


One of the SSPA sidepanels seen from inside the cabinet.
The picture above shows how one of the side panels is equipped. Clicking the picture will make the text on the picture readable.

73 from OZ1BXM Lars Petersen  Visit my homepage: www.oz1bxm.dk


fredag den 1. marts 2013

SSPA for 2 meters - 1 kW module

If you want to explore more details of the amplifier project, I recommend an article by W6PQL: "Solid state 1 kW Linear Amplifier for 2 Meters". It appeared in QST October 2012.

I decided to buy the amplifier module as a kit from James Klitzing, W6PQL, where all components were included. The copper heat spreader, however, was purchased from PE1RKI Bert. I opted for the version prepared for watercooling.

The core of the SSPA is the 1 kW amplifier module. The module is built around the LDMOS transistor MRFE6VP61K25H from Freescale. This device can operate between 1.8 MHz and 600 MHz and delivers 1250 W output. In this application, the output is limited to 1000 W.

The photo below shows how small the 1 kW module is. Dimensions are 12 cm x 8 cm. But the copper heat spreader is 2 cm thick and weights 1.5 kg. This size is necessary, because the heat spreader must be able to transfer up to 400 W.

1 kW amplifier module for 2 meters.


A low-pass filter follows the amplifier module in order to suppress harmonics of 144 MHz. The physical size of the PCB is the same as the amplifier module. A directional coupler is included, which allows monitoring of forward and reverse power.

1 kW low-pass filter for 2 meters.

This project is still in progress and the 'smoke test' should be completed soon.

Lars Petersen, OZ1BXM

Homepage: http://oz1bxm.dk 


fredag den 1. februar 2013

SSPA for 2 meters - Watercooling

The primary advantage of watercooling is its ability to transport heat away from the source (a transistor) to a secondary cooling surface (a radiator). This allows for large, more optimally designed radiators rather than small fins mounted directly on the heat source.

The disadvantage of watercooling is higher cost and complexity when compared to air cooling.

The picture below shows the components in a watercooled system. In my project, the PA transistor is soldered directly to the copper water block. The radiator is mounted on top of the cabinet and cooled by two large 140 mm fans. The pump and the reservoir is one single unit making the system more compact.

The watercooling system for my SSPA project is about twice as expensive as conventional air cooling. In return, I expect a quiet system which allows high-power transmission and human conversation in the schack at the same time!

OZ1BXM Lars Petersen

Homepage: http://oz1bxm.dk/

tirsdag den 1. januar 2013

SSPA for 2 meters - Cabinet

Building a Solid State Power Amplifier (SSPA) is my project this winter. I have chosen the 1 kW SSPA for 144 MHz as described by F1JRD in DUBUS 4/2010. I'll attempt 2 meter EME later this year, and a powerfull SSPA will become a key component in the set-up.

I have decided to build the cabinet first. I have found DIY alu-frames that can be taylored to many sizes. The cabinet's alu-framework is 30 cm wide, 15 cm high, and 15 cm deep. Furthermore, 2 mm alu-sheets are available from another source, and these sheets fit exactly into the alu-framework. This means no cumbersome cutting and bending of cabinet parts!

The SSPA cabinet.

Another feature of my new SSPA is watercooling. This cooling method is known and used among PC freaks. But as far as I know, only few radio amateurs use that technique. More on watercooling next month.

OZ1BXM Lars Petersen

My homepage: oz1bxm.dk

My latest 10 QSO