WAZ wallpaper received

I earned WAZ some time ago. Upon submitting my application, I received a message, that my application was approved and an award number was issued. About 6-8 months later, the wallpaper arrived in the mail. It was a great moment holding the real certificate in my hand!

WAZ #9053 Mixed Mode.

I have now completed my homepage on this pursuit: In pursuit of WAZ - done. 

The next award I will be chasing is QRP DXCC from ARRL. My currrent standing is 85 entities.  

73 from OZ1BXM Lars

Homepage: oz1bxm.dk

1 kW dummy load with fan cooling

I was looking for a big dummy load in connection with my EME-project. Output 1 kW at 144 MHz from the SSPA cannot be terminated into small dummyloads. I needed a "grown up" load.

I decided to build a dummyload with active cooling. A big heat-sink was found on Ebay.de. It was converted into a heat-duct and 2 large fans were fitted at one end. The heat duct was mounted vertically so that cold air can be taken in below, and hot air will be blown out on the top.

Two 800 W resistors, each 100 ohm, were connected in parallel to serve as one large 50 ohm resistor. The resistor array was covered by a metal box to avoid RF radiation. A heat sensor was employed so the heat sink temperature can be displayed on an external digital voltmeter.

1 kW dummy load. Two large fans provide cooling.

The dummy load works to my satisfaction. The frequency range is 0 - 500 MHz. The SWR at 

144 MHz is 1.3. I can now run SSPA tests at full power for long periods of time without overheating.

73 from OZ1BXM Lars Petersen
Homepage: oz1bxm.dk

2 x 8 element yagi for EME

Which type of antenna is suitable for EME? I have been pondering this question for a long time. Now I have decided to put up two 8 element yagi antennas with elevation. They will be mounted vertically, and they will fit nicely on my roof due to their modest size. The array will be elevated by my Yaesu G-550 rotor.

One of the deciding factors in choosing this array was Moon time. Using elevation, many operating hours each day will be available.

Another factor was simplicity. It is easier to mount two yagis vertically than horizontally, and the mechanical balance is good.

Two 8-element yagis.

What is the expected gain of this array? As each 8 element yagi provides 11 dBd, an array with two antennas should provide 3 dB more; that is 14 dBd (25 times). I hope this antenna gain is sufficient for EME with JT65B. By using 1 kW of output power from my newly built SSPA, the total ERP on 144 MHz will be 25 kW.

OZ1BXM Lars Petersen

Wireless internet access

A ham operator needs connecting to the internet when travelling or operating outside his QTH. But why does a ham operator need internet access?

• Download DX information, e.g. from DX Summit
• Upload log files, e.g. to Clublog
• Upload contacts to eQSL and LotW
• Synchronize PC-clock with NTP server (when running JT65 modes)

To enable mobile internet access, I've purchased a Huawei Mobile Broadband USB surfstick (see picture below). The USB surfstick contains a 2G/3G modem. The modem is only used for data transport, not for speech. This device enables internet access in most locations in Denmark.

Huawei E3531 Mobile Broadband modem with SIM card (top cover removed).

Installation is super easy. Just plug the surfstick into your Windows 7 PC and wait for the drivers to install. The surfstick has a local homepage, where you can follow data sent and received, and monitor the signal strength. 

My operator is OiSTER and they utilize the mobile network owned by 3 Denmark. Roaming is not allowed. 

OZ1BXM Lars Petersen

Homepage: oz1bxm.dk

Vacation

Time for vacation! I'll return to this blog with new contributions in September. Until then: Have a nice vacation, all of you!

73 from OZ1BXM Lars Petersen
Homepage: oz1bxm.dk

Stable LO for 23 cm, Multiplier

The task of the EME1152-MLT multiplier is to double the 576 MHz signal generated by the EME175 oscillator. The result is a clean 1152 MHz signal at +16 dBm, which is attenuated to +7dBm and fed to the DBM (mixer) in the 23 cm converter.

The first stage in the multiplier is the GALI-39. It generates several strong harmonics of 576 MHz. Next stage is a tunable filter, which selects the 2. harmonic (1152 MHz) and suppress other frequencies. The two variable capacitors in the tunable filter can be seen near the center of the PCB. Last stage is a GALI-6 which amplifies the desired signal and provides +16 dBm output.

The finished EME1152-MLT print. 

Working with SMD components is difficult in the beginning. But "practice makes perfect" and you get used to the small parts and small distances. I really like to assemble SMD projects, but you need the right tools for the job. A temperature controlled soldering iron with replacable tips; some thin soldering wire (0.5 mm diameter); and a magnifying glass are necessary tools. You will also need a wooden tooth-pic for securing the component while soldering it the first time.

73 from OZ1BXM Lars Petersen
Homepage: oz1bxm.dk

Stable LO for 23 cm

I have started building a stable Local Oscillator (LO) for my 23 cm transceiver. The LO consists of two parts:

• Crystal oscillator for 576 MHz   
• Multiplier for 1152 MHz 

I'll build both modules from kits sold by Mini-Kits in Australia. This company has reasonable prices, and shipping via air from Adelaide to Holstebro, Denmark took only 5 days!  The oscillator kit has number EME175 (I ordered the 400-600 MHz version). The multiplier kit has number EME1152-MLT. Both kits are high-quality products and they are not intended for the new ham - SMD soldering is required!

Crystal oscillator - EME175

In the picture above, you can see an oscillator heater on the left side next to the 96 MHz crystal. The oscillator heater keeps the crystal temperature constantly at 60 degrees centigrade. The heater has number EME177 and uses only 60 mA after warm-up. 

73 from OZ1BXM Lars Petersen

My homepage: A Tiny QRP Page from OZ1BXM

My mail: oz1bxm@pobox.com